Note: a3qjEXAMPLEffp is just an example endpoint, your endpoint URL should replace it. You should create command as format below:ĪT THING_Set=98c6, .com, -–BEGIN CERTIFICATE-–\n…base64 data…\n-–END CERTIFICATE-–\n, -–BEGIN RSA PRIVATE KEY-–\n…base64 data…\n-–END RSA PRIVATE KEY-–\n Step 5: Define and store Thing-specific configuration using AT THING_Set commandĬlient certificate: Certificate for this Thing (downloaded in 3.1 step 3)Ĭlient private key: Private key for this Thing (downloaded in 3.1 step 3) Step 4: Connect to the AP: AT WIFI_Connect Step 3: Set and store information of the AP using AT WIFI_SetAP= MySSID,MyPassword,wpa2ĪT WIFI_SetAP=SSID,password,security type Step 2: Check if AW-CU427-USB is in station mode using AT WIFI_GetMode Turn on the Wi-Fi module of the AW-CU427-USB using AT WIFI_On Hardware Setup) and turn off the wireless devices near the AW-CU427-USB (except for the device under test). Step 1: Connect the AW-CU427-USB to the system (refer to 2. USB BLOCK 1.7.1 REGISTRATION CODE PASSWORDAssume the SSID, password and security type of the AP is MySSID, MyPassword, wpa2. Step 0: Make sure the AP under test is connected to the internet using other Wi-Fi enabled devices. You can find out thing name in Manage > Things submenu, and endpoint in settings of AWS IOT Console at /iot.ģ.2 Publish and Monitor MQTT message on the cloud These two data will also be used for AT THING_Set command. Because they will be used when sending the AT THING_Set command. USB BLOCK 1.7.1 REGISTRATION CODE DOWNLOADIn Create and activate a device certificate chapter, please download and keep the certificate and private key. Please refer to the steps at the following link.Īfter finishing the steps, please notice the following two actions: After provisioning, you can connect to AWS IOT with MQTT or SHADOW operation. After this command executing, the four parameter will be provision to our connector. You can use certificate, private key, thing name and endpoint as AT THING_Set command parameter. This step will create certificate and private key. Please refer to the following link to create a thing. If you have created an IAM user, please refer to the following setting to connect these two policies (AmazonFreeRTOSFullAccess, AWSIoTFullAccess) to your IAM.Ī thing represents a specific device or instance that can communicate with AWS IOT. Please refer to the below link to setup AWS Account and IAM user. Step 1: Create AWS Account, Create an IAM user. USB BLOCK 1.7.1 REGISTRATION CODE HOW TOStep 0: The below link is a documents of how to setup AWS IOT, you can refer to it for full AWS IOT knowledge.īut, if you want to setup AzureWave AWS Connector, you would just refer to the following steps. Qos: 0 | 1 3.1 Getting Started with AWS IoT Core Subscribe to and save MQTT topic: AT MQTT_Subscribe=,.Connect the client to MQTT broker: AT MQTT_Connect.Define and store Thing-specific configuration:ĪT THING_Set=client ID,endpoint,client certificate,client private keyĬlient certificate: Certificate for this ThingĬlient private key: Private key for this Thing.Password: password for AP (case sensitive) Set and store the Wi-Fi AP information when AW-CU427-USB in Station Mode:ĪT WIFI_SetAP=SSID,password, security type.Perform a Wi-Fi network scan: AT WIFI_Scan. Retrieve the Wi-Fi AP | Station Mode: AT WIFI_GetMode.Please find the command details in AWS CONNECTOR AT Command Set. Wood Desk
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |